All Purpose Plastisol Ink – White – For Cotton, Polyester & Blends

All Purpose White Plastisol Ink is the white to match our do-it-all All Purpose line — a high-opacity, low-bleed white that prints on all three fabric types (100% cotton, 50/50 blends, and light-color polyester), direct or as a bright flash underbase. It's stretchable, cures at 300–310°F, and lays down creamy and print-ready. CPSIA-compliant and phthalate-free, made in Hackensack, New Jersey.

Pint through 55 gallon. Heat cure. Made in the USA.

Also available in larger quantities — 30-gallon and 55-gallon drums; call 201-487-9600 for volume and discount pricing.

Features & benefits

• Prints on all three fabrics — 100% cotton, 50/50 blends, and light-color polyester
• High opacity — bright, dense white coverage on darks
• Dependable flash underbase — solid base for colors on dark garments
• Low-bleed & stretchable — clean coverage that moves with the garment
• Creamy & print-ready — smooth lay-down on manual or automatic presses
• Pint to 55 gallon — stock sizes plus drums for production shops
• CPSIA-compliant & phthalate-free — safe for kids' apparel, made in the USA

Always run a test print first. Before any production run, print and fully cure a test on your exact garment and check opacity, hand and wash-fastness. It's the best habit in the shop — if you're not sure on settings, call us at 201-487-9600 before you run the job.

What it prints on

• 100% cotton — full opacity, bright clean white
• 50/50 cotton/poly blends
• Light-color polyester — low-bleed; for dark or high-bleed poly use a grey blocker underbase or an athletic/poly white
• Runs as a flash underbase under bright colors on darks

Printing & curing

• Mesh: 110–160 for maximum opacity; up to 200+ for a lighter deposit
• Squeegee: 65, 75 or 80 durometer — or a 70/90/70 triple durometer
• Flash: 240–260°F when used as an underbase
• Cure: curing is a time-and-temperature process — bring the full ink film to 300–310°F (150–154°C); confirm with a temp gun or donut probe, not dryer air temp

Recommended companion products

• Nylon Bond 289 Additive — mix into this ink to bond prints to nylon and other slick synthetics (catalyst; stir in a small amount, limited pot life, always test first).
• Quick Flash Reducer — thins for easier printing.
• Soft Hand Base — softer hand feel.
• Pantone® Custom Color Match — send us your target Pantone® and we custom-mix the color for you (plastisol, solvent, UV & water-base).
• Cleanup: OPTI Wash 125 and OPTI Spot 303.

How close are we to your Pantone?

See our Standard Color → Pantone® (PMS) Match Chart — the closest Pantone® reference for every Total Ink Solutions standard color, with RGB and HEX values. For an exact, verified match, our UMX® system mixes to your target.

Safety, PPE & storage

• Wear nitrile gloves and safety glasses; avoid prolonged skin contact with uncured ink.
• Print with adequate ventilation; vent your dryer.
• Always stir before use.
• Storage & shelf life: keep sealed, out of sun. Shelf life 1–2 years; low-cure and all-polyester inks store at 60–80°F. In high heat expect container expansion — open carefully. Do not freeze.
• Refer to the Safety Data Sheet before use.

Compliance

CPSIA compliant (16 CFR 1303 <90 ppm; CPSIA §101 <100 ppm total lead) — safe for children's apparel. Phthalate-free.

⚠ WARNING (California Proposition 65): This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Questions?

Total Ink Solutions
200 South Newman Street, Unit 4 & 5
Hackensack, NJ 07601
Phone: 201-487-9600 · Fax: 201-487-9620
Email: sales@totalinksolutions.com